Blank Cover Image

工具-加工物接触面温度の測定

フォーマット:
論文
責任表示:
上田, 隆司 ; 佐藤, 昌彦 ; 杉田, 忠彰
言語:
日本語
出版情報:
精密工学会 = The Japan Society for Precision Engineering, 1995-10-05
著者名:
掲載情報:
精密工学会誌 = Journal of the Japan Society of Precision Engineering
ISSN:
0912-0289  CiNii Research  Webcat Plus  JAIRO
巻:
61
通号:
10
開始ページ:
1448
終了ページ:
1452
バージョン:
publisher
概要:
Temperature of interface between a cutting tool and a workpiece is measured using two-color pyrometer with a fused fiber coupler. A conical tool is used as the cutting tool which is made of translucent alumina sintered under HIP, and 0.55% carbon steel is used as a workpiece. The infrared rays radiated from the interface and transmitted through the conical tool are accepted by a fused fiber coupler and led to two infrared detectors of different spectral sensitivity. Temperature is obtained by calculating the ratio of the output voltage from these two detectors. The results obtained are as follows. The temperature increases very rapidly and reaches 1000°C at about 40 μs after the beginning of cutting. The rate of increase of temperature is very great : about 108 °C/s at the cutting speed of 1 500 m/min. The temperature increases with the increase of cutting speed, but at a speed faster than 1000 m/min its influence is small. The temperature shows a tendency to saturate about 1300-1400°C as the cutting speed increases. 続きを見る
URL:
http://hdl.handle.net/2297/38879
タイトル・著者・出版者が同じ資料

類似資料:

1
 
2
 
3
 
4
 
5
 
6
 
7
 
8
 
9
 
10
 
11
 
12
 

佐藤, 昌彦, 上田, 隆司, 西田, 昌弘

精密工学会 = The Japan Society for Precision Engineering

田中, 隆太郎, 山根, 八洲男, 岡田, 将人, 細川, 晃, 上田, 隆司

精密工学会 = The Japan Society for Precision Engineering

上田, 隆司, 入山, 孝宏, 杉田, 忠彰

精密工学会 = The Japan Society for Precision Engineering

千徳, 英介, 上田, 隆司, 山田, 啓司, 細川, 晃

精密工学会 = The Japan Society for Precision Engineering

Al Huda, Mahfudz, 山田, 啓司, 上田, 隆司

精密工学会 = The Japan Society for Precision Engineering

上田, 隆司, 山田, 啓司, 及川, 志郎, 細川, 晃

精密工学会 = The Japan Society for Precision Engineering

上田, 隆司, 佐藤, 昌彦, 杉田, 忠彰

精密工学会 = The Japan Society for Precision Engineering

佐藤, 昌彦, 上田, 隆司, 田中, 久隆

精密工学会 = The Japan Society for Precision Engineering

細川, 晃, 小田, 健作, 山田, 啓司, 上田, 隆司

精密工学会 = The Japan Society for Precision Engineering

上田, 隆司, 佐藤, 昌彦, 金田, 泰幸, 杉田, 忠彰

精密工学会 = The Japan Society for Precision Engineering

山崎, 修平, 田中, 隆太郎, 細川, 晃, 上田, 隆司, 古本, 達明

精密工学会 = The Japan Society for Precision Engineering