※一部利用できない機能があります
| 1.
論文 |
論文
|
細川, 晃 ; 南部, 彰 ; 田中, 隆太郎 ; 山田, 啓司 ; 上田, 隆司 ; Hosokawa, Akira ; Nambu, Akira ; Tanaka, Ryutaro ; Yamada, Keiji ; Ueda, Takashi
概要:
金沢大学理工研究域機械工学系<br />前報では光ファイバ型2色温度計を用いてエンドミル加工におけるオイルミスト供給時の工具逃げ面温度を測定し,ミスト粒径,ミスト流量,ミスト供給位置が工具逃げ面温度に及ぼす影響について検討した.本報では,そ
…
の第3段階として,超硬工具およびコーティング工具における切削温度と工具損耗量を測定し,オイルミスト供給が工具損耗形態に及ぼす影響について詳細に検討している.<br />出版者照会後に全文公開
続きを見る
|
||||
| 2.
論文 |
論文
|
上原, 祐也 ; 細川, 晃 ; 上田, 隆司 ; 田中, 隆太郎 ; 古本, 達明
概要:
難削材旋削加工における新しい技術として、ADRT（スピニングツール）が提案された．ADRTでは工具自身が回転するため，切れ刃の加熱(切削時)-冷却(空転時)サイクルが制御でき，工具寿命の増大が期待される．しかしながら，その加工特性は明らかに
…
なっていない．そこで本研究では，非接触で微小領域の温度測定が可能な光ファイバ型２色温度計を用いて，スピニングツールの加熱－冷却特性を測定し，工具への熱負荷の面から本手法の有効性を検討している． Turning characteristics of austenitic stainless steel SUS304 with an actively driven rotary lathe tool is invented from the thermal aspects. The tool temperature during one revolution of this spinning tool is measured using a newly assembled two-color pyrometer. There is an optimum tool rotational speed at which the tool temperature is at a minimum with respect to the cutting conditions.
続きを見る
|
||||
| 3.
論文 |
論文
|
Al Huda, Mahfudz ; 山田, 啓司 ; 上田, 隆司
概要:
The temperature of the flank side of the cutting tool edge that has large affect on machined surface integrity is measur
…
ed using two-color pyrometer with a fused fiber coupler. The infrared rays radiated from the cutting tool edge are accepted by an optical fiber, and separated to two optical fibers at the fused fiber coupler. Each fiber leads the infrared ray, respectively, to two infrared detectors with different characteristic of spectral sensitivity. Temperature is obtained by calculating the ratio of the output voltage from these two detectors. A CBN tool (CBN content : 60 volume percent, density : 3000 kg/mm2) is used as the cutting tool. Annealed steel (S45C), bearing steel (SUJ2), and quenched steel (S55C) are used as the cutting materials to investigate their affect on the tool edge temperature. The results obtained are as follows : (1) The technique developed is suitable for measuring the temperature of the flank side of the cutting tool edge. (2) The temperature of the cutting tool edge is highly effected by cutting speed. (3) The temperature increases slightly with the increase of depth of cut and feed rate. (4) On the cutting of quenched steel which has the largest hardness among these three materials, the temperature is about 50°C higher than that on the bearing steel cutting, and the temperature of the annealed steel cutting is the lowest.
続きを見る
|
||||
| 4.
論文 |
論文
|
細川, 晃 ; 小澤, 匡史 ; 田中, 隆太郎 ; 古本, 達明 ; 上田, 隆司
概要:
In this paper, the MQL turning of two types of ferrous metals: chromium-molybdenum steel SCM440H and pearlite malleable
…
cast iron FCMP: is dealt with. The appropriate generating system of oil mist is constructed and the specified turning tool with oil hole is used. In order to verify the cooling effect of MQL, the tool temperature at the flank face is measured using a newly assembled fiber-coupled two-color pyrometer. In this new technique, a sensing fiber is inserted into a small hole that extends to the outer surface of the tubelike workpiece and it rotates with the workpiece. The thermal radiation accepted by a sensing fiber is noncontactly transmitted to the other fixed fiber and led to the two-color detectors. As for cutting force in turning of SCM440H, MQL is more effective in low cutting speed below 100 m/min. The tool temperature in MQL turning is approximately 100°C lower than that in dry turning over the wide range of 30∼300 m/min. In the case of FCMP, the tool temperature in dry turning at a cutting speed of 600 m/min reaches as much as about 1040°C, but it drops 920°C in MQL turning.
続きを見る
|
||||
| 5.
論文 |
論文
|
西本, 秀人 ; 田中, 隆太郎 ; 細川, 晃 ; 上田, 隆司 ; 古本, 達明
概要:
本研究では湿式切削における2色温度計を用いた工具刃先温度の測定方法を提案する．光ファイバを挿入した小孔からエアを供給することでクーラントが光ファイバ端面へ付着することを防ぎ，湿式切削における温度測定が可能となる．この方法によってダイヤモンド
…
焼結体工具およびCBN焼結体工具を用いたチタン合金の湿式切削において，工具刃先温度の測定を行った． In this study, the method of tool edge temperature using two-color pyrometer in wet cutting is proposed. Using this method, the high pressure air supplied from small hole for an optical fiber prevents coolant from adhering to the optical fiber edge and makes temperature measuring possible. Air pressure never affects tool edge temperature measured using two-color pyrometer. In this way, the tool edge temperature of CBN and Poly Crystalline Diamond (PCD) tool is measured in turning of Ti-6Al-4V. As a result, the tool edge temperature is increases rapidly with the increase of cutting speed. In dry turning of Ti-6Al-4V, PCD tool edge temperature is almost 100oC lower compared with CBN tool edge temperature. Supplying coolant, CBN tool edge temperature is reduced about 70 oC and PCD tool edge temperature is reduced about 340 oC compared with tool edge in dry turning resistivity.
続きを見る
|
